Craftsman T3200 Riding Mower Parts Manual

The Craftsman T3200 is a powerful riding lawn mower featuring a 24 HP Briggs & Stratton engine, 46-inch cutting deck, hydrostatic transmission, electric PTO, and a comfortable high-back seat. This manual provides detailed parts identification, diagrams, and ordering information for maintenance, repair, and replacement. Below are key sections covering safety, parts diagrams, specifications, assembly instructions, and troubleshooting.

1. Parts Overview & Diagrams 2. Engine Components 3. Cutting Deck Assembly 4. Drive & Transmission 5. Electrical System 6. Controls & Operator Station 7. Wheels & Tires 8. Maintenance Parts 9. Assembly Instructions 10. Parts Ordering Information 11. Troubleshooting & Service

Parts Overview & Diagrams

Key assemblies: Engine, Cutting Deck, Drive System, Electrical, Controls, Frame.

AssemblyMain Components
Engine (Briggs & Stratton)Cylinder, carburetor, air filter, oil filter, spark plug, fuel pump
Cutting Deck (46")Blades, spindles, belt, deck shell, baffles, anti-scalp rollers
Drive SystemHydrostatic transmission, drive belt, axle, pulleys
Electrical SystemBattery, starter, solenoid, ignition switch, safety switches, wiring harness
ControlsSteering wheel, brake pedal, throttle, PTO switch, gear selector
Frame & BodyFrame rails, fenders, seat, footrests, hood

Engine Components

24 HP Briggs & Stratton Intek V-Twin engine parts list.

  1. Cylinder & Piston: Piston rings, connecting rod, gaskets.
  2. Fuel System: Carburetor (part #123456), fuel filter, fuel lines, fuel tank.
  3. Air Intake: Air filter element, pre-cleaner, housing.
  4. Ignition: Spark plugs (Champion RC12YC), ignition coil, flywheel.
  5. Lubrication: Oil filter, dipstick, oil drain tube.
  6. Cooling: Cooling fins, blower housing, fan.

WARNING! Disconnect spark plug wire before servicing engine. Use genuine Briggs & Stratton parts.

Cutting Deck Assembly

46-inch stamped steel deck with three blades.

  1. Blades: High-lift blades (part #789012), blade bolts, washers.
  2. Spindles: Spindle assembly (includes bearings, pulley, housing).
  3. Belt: Deck drive belt (part #345678), idler pulleys, tension spring.
  4. Deck Shell: Main deck, skid shoes, discharge chute.
  5. Anti-scalp Rollers: Front and rear rollers, mounting brackets.

CAUTION! Ensure deck is properly leveled after parts replacement. Always disconnect PTO and remove key.

Drive & Transmission

Electrical System

12-volt system with safety interlock switches.

Components: Battery (12V, 280 CCA), starter motor, ignition key switch, PTO clutch, headlight, fuse (20A), wiring diagram included.

Safety Switches: Seat switch, brake switch, PTO switch, reverse operation switch.

Controls & Operator Station

Steering wheel, brake pedal, throttle, PTO switch, gear selector.

  1. Turn off engine and remove key before adjusting controls.
  2. Check linkage for wear; replace if loose.
  3. Lubricate pivot points with grease.

Tip: Adjust seat position for comfortable operation and easy access to controls.

Wheels & Tires

Front: 15x6.00-6 tires. Rear: 20x10.00-8 tires.

  1. Front Axle: Spindle, bushings, washers.
  2. Rear Wheels: Wheel hub, lug nuts, valve stem.
  3. Tire Pressure: Maintain 12 PSI (front), 10 PSI (rear).

WARNING! Do not over-inflate tires. Check for cracks or wear.

Maintenance Parts

Oil filter (Briggs & Stratton 492932S), air filter, spark plug, fuel filter, blades, belts, battery.

CAUTION! Use only recommended parts. Follow maintenance schedule in operator's manual.

Assembly Instructions

For new mower assembly or major component replacement.

  1. Attach steering wheel: Align and tighten bolt.
  2. Install seat: Mount with provided bolts and washers.
  3. Attach cutting deck: Connect lift linkage, belt, and anti-scalp rollers.
  4. Connect battery: Red to positive, black to negative.
  5. Check fluid levels: Engine oil, transmission fluid.

Note: Refer to detailed assembly diagram for torque specifications.

Parts Ordering Information

Use model number (917.273xxx) and part numbers from diagrams. Order from authorized Craftsman dealers or www.craftsman.com. Keep receipt for warranty claims.

Troubleshooting & Service

SymptomPossible CauseCorrective Action
Engine won't startDead battery, bad spark plug, clogged fuel filterCharge/replace battery; check spark plug; replace fuel filter.
Poor cutting performanceDull blades, worn belt, deck not levelSharpen/replace blades; adjust belt tension; level deck.
Loss of powerClogged air filter, old oil, transmission issueClean/replace air filter; change oil; check transmission fluid.
VibrationUnbalanced blade, loose spindle, damaged pulleyBalance blade; tighten spindle bolts; inspect pulleys.
Hydrostatic transmission slipsLow fluid, worn belt, internal wearCheck fluid level; replace drive belt; service transmission.

Service: For technical support, call 1-888-331-4569 or visit www.craftsman.com.

Craftsman T3200 Riding Mower Parts Manual © - All Rights Reserved 2025